VDO RESSURE GAUGE Spécifications télécharger pdf

06/11

INSTALLATION INSTRUCTIONS: Viewline 52 mm

Temperature gauge, pressure gauge, rudder angel gauge,

trim gauge, fuel gauge, fresh water gauge for level-type sensor

TU00-0752-5207102

1-6

Technische Änderungen vorbehalten - Technical details subject to change

TU00-0752-5207102

Safety information

• The product was developed, manufactured and inspected

according to the basic safety requirements of

EC Guidelines and state-of-the-art technology.

• The instrument is designed for use in grounded vehicles and

machines as well as in pleasure boats, including non-classified

commercial shipping.

• Use our product only as intended. Use of the product for reasons

other than its intended use may lead to personal injury, property

damage or environmental damage. Before installation, check the

vehicle documentation for vehicle type and any possible special

features!

• Use the assembly plan to learn the location of the fuel/hydraulic/

compressed air and electrical lines!

• Note possible modifications to the vehicle, which must be considered

during installation!

• To prevent personal injury, property damage or environmental

damage, basic knowledge of motor vehicle/shipbuilding electronics

and mechanics is required.

• Make sure that the engine cannot start unintentionally during

installation!

• Modifications or manipulations to VDO products can affect safety.

Consequently, you may not modify or manipulate the product!

• When removing/installing seats, covers, etc., ensure that lines are

not damaged and plug-in connections are not loosened!

• Note all data from other installed instruments with volatile electronic

memories.

Safety during installation:

•

During installation, ensure that the product’s components do not

affect or limit vehicle functions. Avoid damaging these components!

• Only install undamaged parts in a vehicle!

• During installation, ensure that the product does not impair the field

of vision and that it cannot impact the driver’s or passenger’s head!

• A specialized technician should install the product. If you install the

product yourself, wear appropriate work clothing. Do not wear loose

clothing, as it may get caught in moving parts. Protect long hair with

a hair net.

• When working on the on-board electronics, do not wear metallic or

conductive jewelry such as necklaces, bracelets, rings, etc.

• If work on a running engine is required, exercise extreme caution.

Wear only appropriate work clothing as you are at risk of personal

injury, resulting from being crushed or burned.

• Before beginning, disconnect the negative terminal on the battery,

otherwise you risk a short circuit. If the vehicle is supplied by auxil-

iary batteries, you must also disconnect the negative terminals on

these batteries! Short circuits can cause fires, battery explosions and

damages to other electronic systems. Please note that when you

disconnect the battery, all volatile electronic memories lose their input

values and must be reprogrammed.

• If working on gasoline boat motors, let the motor compartment fan

run before beginning work.

• Pay attention to how lines and cable harnesses are laid so that you

do not drill or saw through them!

• Do not install the product in the mechanical and electrical airbag

area!

• Do not drill holes or ports in load-bearing or stabilizing stays or tie

bars!

• When working underneath the vehicle, secure it according to the

specifications from the vehicle manufacturer.

• Note the necessary clearance behind the drill hole or port at the

installation location. Required mounting depth: 65 mm.

• Drill small ports; enlarge and complete them, if necessary, using

taper milling tools, saber saws, keyhole saws or files. Debur edges.

Follow the safety instructions of the tool manufacturer.

• Use only insulated tools, if work is necessary on live parts.

• Use only the multimeter or diode test lamps provided, to measure

voltages and currents in the vehicle/machine or boat. Use of conven-

tional test lamps can cause damage to control units or other elec-

tronic systems.

• The electrical indicator outputs and cables connected to them must

be protected from direct contact and damage. The cables in use

must have sufficient insulation and electric strength and the contact

points must be safe from touch.

• Use appropriate measures to also protect the electrically conductive

parts on the connected consumer from direct contact. Laying metal-

lic, uninsulated cables and contacts is prohibited.

Safety after installation:

• Connect the ground cable tightly to the negative terminal of the

battery.

• Reenter/reprogram the volatile electronic memory values.

• Check all functions.

• Use only clean water to clean the components. Note the Ingress

Protection (IP) ratings (IEC 60529).

Electrical connection:

•

Note cable cross-sectional area!

• Reducing the cable cross-sectional area leads to higher current

density, which can cause the cable cross-sectional area in question

to heat up!

• When installing electrical cables, use the provided cable ducts and

harnesses; however, do not run cables parallel to ignition cables or

to cables that lead to large electricity consumers.

• Fasten cables with cable ties or adhesive tape. Do not run cables

over moving parts. Do not attach cables to the steering column!

• Ensure that cables are not subject to tensile, compressive or

shearing forces.

• If cables are run through drill holes, protect them using rubber

sleeves or the like.

• Use only one cable stripper to strip the cable. Adjust the stripper

so that stranded wires are not damaged or separated.

• Use only a soft soldering process or commercially available crimp

connector to solder new cable connections!

• Make crimp connections with cable crimping pliers only. Follow the

safety instructions of the tool manufacturer.

• Insulate exposed stranded wires to prevent short circuits.

• Caution: Risk of short circuit if junctions are faulty or cables are

damaged.

• Short circuits in the vehicle network can cause fires, battery explo-

sions and damages to other electronic systems. Consequently,

all power supply cable connections must be provided with weldable

connectors and be sufficiently insulated.

• Ensure ground connections are sound.

• Faulty connections can cause short circuits. Only connect cables

according to the electrical wiring diagram.

• If operating the instrument on power supply units, note that the

power supply unit must be stabilized and it must comply with the

following standard: DIN EN 61000, Parts 6-1 to 6-4.

No smoking! No open fire or lights!

1 2 3 4 5 6